|
ELEPHANT SNOT Graffiti Remover
ELEPHANT SNOT® Graffiti Remover is custom formulated for specific
removal needs. If it is a "porous" surface, then ELEPHANT SNOT
Graffiti Remover is the right choice for the job. It is the workhorse for the
most difficult of porous surface removal requirements - ELEPHANT SNOT
penetrates deeply into concrete, cement, brick, grout, stone, virtually
anything porous to dissolve and loosen all types of tags, and in many
circumstances, simple water hose pressure will do the job.
Recommended for removal on:
Brick, mortar, masonry, cement, concrete, stucco, terrazzo,
landscaping pavers, porous tile. Natural stone surfaces such as granite,
marble, sandstone, rocks, both porous/rough or polished. Also effective on:
glass, ceramic, porcelain, glazed tiles, porous tile, grout.
Features & Benefits:
•Non-drip formula for easy application without messy runs and
drips.•Fast removals - clings to the surface for maximum penetration and
maximum speed of removal
•Low odor with minimum or no ventilation requirement for added
safety, indoors or out.
•Water hose pressure removal option for "no pressure washer
required" benefits.
•Nonflammable, non-combustible, minimal fire hazard formulary.
•All temperature effective removals from freezing cold to "very
hot" conditions.
|
|
General Instructions:
•STIR BEFORE USE.
•ELEPHANT SNOT should not be used for any other purpose/removal,
without thoroughly testing in an inconspicuous area for effect.
•Apply by brush or roller. Water cleanup recommended after each use.
•Allow to penetrate affected areas for 15-20 minutes (30-40 minutes
in cold temperatures).
•Use power washer with 15° tip with 1000 - 3000 PSI maximum pressure.
For optimum performance and removal speed use hot water (190°F). Excellent
results may be obtained with a Cold Water Power Washer with the above
specificiations by doubling the dwell time (30-40 minutes).
•Alternative Method: Allow to penetrate for 30-35 minutes, agitate
with stiff brush, and remove with water hose at maximum nozzle pressure.
•Repeat process if necessary.
•Use SHADOW MAX® to remove any ghosting or shadow.
•Clean up all equipment after each use with water.
Safety Instructions For Use:
•Always wear protective eyewear and chemical resistant gloves. Can
cause burns.
•Protect all exposed skin areas with chemical resistant covering.
•If product gets on skin, wash off immediately. If product gets in
eyes, flush with water for 15 minutes.
•FOR PROFESSIONAL USE ONLY
|
|
BEFORE
|
AFTER
|
Method:
Applied one coat Elephant Snot® with brush, dwell time was 2 minutes.
Removed with 190 degree water at 2500 psi with a 15 degree tip.
Place:
White Bear Lake, MN
Job Time:
5 minutes
Substrate:
Brick wall - School
Job Notes:
Spray paint on brick. Outside air temperature was 80 degrees.
|
|
Specifications
Consistency: No drip gel clings to vertical surfaces without
dripping.
Coverage: 100 to 200 Sq. ft./gal. depending on porosity of surfaces.
Use Temperatures: Use in temperatures down to 25 degrees, will work
slower at cold temperature.
Storage: Stores between 40°F and 130°F. DO NOT FREEZE. If frozen,
thaw and remix before using. Keep out of the reach of children.
Flammability: Nonflammable, non-combustible. Flash point over 200°F.
V.O.C.'s: .4 Ibs/gallon, 50 grams/liter H.A.P.S. - none.
Volatility: Very low rate of evaporation. No ventilation required
unless used in a confined space.
Biodegradable: Yes
Shipping: Not regulated, D.O.T. Proper shipping name: Cleaning
Compound N.O.S., Class 55.
Effective On: Paint spills on floors, spray booth oversprays, even
many difficult to remove 2-part paints, epoxy, urethane, can be remove
effectively with ELEPHANT SNOT.
Other Uses:
Removes road tars, asphalt, oils, greases, gum, wax, tree sap, and
many other difficult to remove marks or stains, from all types of porous or
other recommended surfaces.
|
|
BEFORE
|
AFTER
|
Method:
One coat of Elephant Snot® applied with brush, dwell time of 15
minutes. Flushed off with 190 degree hot water at 2500 psi and a 15 degree
tip.
Place:
Saint Paul, MN
Job Time:
30 minutes
Substrate:
Split face cinder block
Job Notes:
Green spray paint graffiti on split face cinder block. Note: Split
face cinder block takes 2-3 days for complete evaporation fo applied chemical
and sprayed water.
|
|
If removing "shadows or ghosts" from any of the above
surfaces, we recommend the use of SHADOW MAX® Graffiti remover for maximum
effectiveness.
For removals from all types of metals, "durable" baked
on painted surfaces such as auto, bus, truck, other factory applied paints,
or fiberglass use our SMOOTH MAX® Graffiti remover.
|
